Commercial Electric CER3LICR3730WH Bedienerhandbuch PDF herunterladen

READ ALL THE INSTRUCTIONS

TOOLS & MATERIALS REQUIRED

QUESTIONS? CALL TOLL FREE

1-800-345-0542

INSTALLATION & OPERATION INSTRUCTIONS –

3” (7,6 mm) IC RECESSED LIGHTING KIT

MODELS: CER3LICR3730

UNPACK THE FIXTURE

Check the contents of the box. You should receive:

• 1 – Housing (can, junction

box)

• 1 - Trim assembly

• 1 – Template

• 3 – Remodel clips (pre-

attached to housing)

• 3 – Wire Nuts

WARNING: First disconnect electricity at the circuit breaker or the fuse box.

Disconnecting power by using the wall switch is not sufficient to prevent

electrical shock.

Choose the location for the fixture(s), keeping in mind the 6” (15,2 cm) depth clearance,

accessibility for the electrical supply, and the ½” (1,3 cm) clearance from the joists, floor

boards, or any other combustible material.

REMODEL INSTALLATION

MAKING THE HOLE/RUNNING THE SUPPLY WIRING TO THE HOLE

1. Cut a 3 1/4” (8,3 cm) hole into the ceiling after choosing the appropriate location. A

template is provided to assist in making the hole. (Fig. 2)

2. Clear out any insulation necessary to maintain the 3” (7,6 cm) spacing specified in

the “CAUTION” section found in the beginning of these instructions. (See Fig. 1)

3. Run armored cable (BX) or non-metallic (NM) cable (also known as Romex) from

your circuit breaker or fuse panel to the 3 1/4” (8,3 cm) hole, providing 6” (15,2 cm)

to 8” (20,3 cm) of slack extending below the hole. Cable having up to 12 AWG wiring

may be used. (Fig. 3) (WARNING - Use cables having wires rated 90°C or more.)

Hole

Ceiling

Cable

Hole

Fig. 2

Fig. 3

Keyhole saw

BEFORE YOU BEGIN

1. To ensure the success of the installation, be sure to read these instructions and

review the diagrams thoroughly before beginning.

2. All electrical connections must be in accordance with local code and ordinances. If

you are unfamiliar with methods of installing electrical wiring, secure the services of a

qualified licensed electrician.

3. Before starting the installation, disconnect electricity at the circuit breaker or the fuse

box. Disconnecting power by using the wall switch is not sufficient to prevent

electrical shock.

4. Check if the power source is suitable for the added electrical load. Power should be

supplied by a 110/120 volt, 60 Hz single circuit. A standard 120 volt, 15 amp branch

circuit is designed to carry a maximum load of 1800 watts. We recommend that the

total wattage of all the lights and appliances on that circuit, not exceed 80% or 1440

watts, of the maximum electrical capacity.

5. This fixture is designed to be used on ceiling surfaces that are 3/8” (1,0 cm),

1/2” (1,3 cm), or 5/8” (1,6 cm) thick. It cannot be used on any other ceiling

thickness.

Out of the box, this product can be use in REMODEL applications. In a remodel

application, a ceiling surface already exists and there is no access above the surface to

the ceiling joists. To install this fixture, a hole must be made in the existing ceiling from

the room side. Then, electrical wiring must be run to this hole and connected to the

fixture. The fixture is, finally, inserted into the ceiling hole, which secures itself to the

ceiling surface, using special remodel clips (provided). To use this product in NEW-

CONSTRUCTION applications, a Commercial Electric plaster frame and

Commercial Electric hanger bars must be purchased, separately. In a new

construction application, the ceiling surface has not yet been installed and the ceiling

joists are still exposed and accessible.

IMPORTANT NOTE

• Ladder

• BX or NM Cable

Connectors

• Keyhole Saw or 3 ¼” (8,3

mm) Hole Saw

• Flathead Screwdriver

• Insulated Pliers

• Pencil

• UL Listed Electrical

Tape

4. Proceed to the “ELECTRICAL CONNECTIONS” section.

1. Slide the housing through the hole opening. (Fig. 4)

MOUNTING THE HOUSING TO THE CEILING

GETTING STARTED

Fig. 4

Hole

Housing

Ceiling

Remodel

clip

Fig. 1

Insulation

CAUTION

Before assembling your lighting fixture, refer to the “ELECTRICAL CONNECTIONS”

section. If you feel you do not have electrical wiring experience, refer to a do-it-yourself

wiring handbook or have your fixture installed by a qualified licensed electrician.

NOTE: This fixture is an IC type fixture. It may come in direct contact with

thermal insulation. It can be completely covered by thermal insulation, as shown

below. In addition, any part of the fixture may come in direct contact with any

combustible material, such as a ceiling joist or floor board. (FIG. 1)

REV 03-DEC-2013

1 2 3 4 5 6 ... 11 12

Inhaltsverzeichnis

Seite 1 - READ ALL THE INSTRUCTIONS

READ ALL THE INSTRUCTIONSTOOLS & MATERIALS REQUIREDQUESTIONS? CALL TOLL FREE 1-800-345-0542INSTALLATION & OPERATION INSTRUCTIONS –3” (7,6 mm

Seite 2 - NEW CONSTRUCTION INSTALLATION

Seite 3 - DROP CEILING INSTALLATION

L'interrupteur ou le disjoncteur est fermé.Ouvrez l'interrupteur ou le disjoncteur.Les connexions électriques sont incorrectes ou lâches.Vér

Seite 4 - MODEL: RHPS311AL-JW1

Seite 5 - LEER TODAS LAS INSTRUCCIONES

1. Raise the plaster frame and hanger bar assembly to the desired location betweenthe two ceiling joists. Adjust the width of both hanger bars to the

Seite 6 - Barra "Hembra"

1. Plug the FEMALE CONNECTOR of the TRIM onto the MALE CONNECTOR of theHOUSING.2. Tuck all wires into the CAN and carefully push the TRIM into CAN.3.

Seite 7 - INSTALACIÓN EN TECHO FALSO

Seite 8 - MODELO: RHPS311AL-JW1

LEER TODAS LAS INSTRUCCIONESHERRAMIENTAS Y MATERIALES NECESARIOS¿PREGUNTAS? LLAMA GRATIS AL 1-800-345-0542INSTRUCCIONES DE INSTALACIÓN Y FUNCIONAMIEN

Seite 9 - LISEZ TOUTES LES INSTRUCTIONS

Seite 10

1. Enchufe el CONECTOR HEMBRA del ADORNO DECORATIVO en el CONECTORMACHO de la CAJA.2. Coloque todos los cables en el Coloque todos los cables en el AL

Seite 11

Seite 12 - MODÈLE: RHPS311AL-JW1

LISEZ TOUTES LES INSTRUCTIONSOUTILS ET MATÉRIAUX NÉCESSAIRESDES QUESTIONS? APPELEZ SANS FRAIS AU 1-800-345-0542MODE D’INSTALLATION ET D’EMPLOI POUR L

Kommentare zu diesen Handbüchern

Keine Kommentare

Commercial Electric CER3LICR3730WH Bedienerhandbuch

Stöbern Sie online oder laden Sie Bedienerhandbuch nach Nein Commercial Electric CER3LICR3730WH herunter. Commercial Electric CER3LICR3730WH Instructions / Assembly Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Commercial Electric CER3LICR3730WH