Commercial Electric CER6730AWH40 Bedienerhandbuch PDF herunterladen

WARNING - RISK OF ELECTRIC SHOCK. DISCONNECT

MAIN POWER AT FUSE OR CIRCUIT BREAKER

BEFORE INSTALLING OR SERVICING THE FIXTURE.

LED5” & 6” RETROFIT TRIM INSTALLATION

INSTRUCTIONS - MODEL CER6730A

QUESTIONS? CALL TOLL

FREE 1-800-345-0542

Please read carefully and save these instructions as

you may need them at a later date.

GENERAL: All electrical connections must be in accordance with

local and National Electrical Code (N.E.C.) standards. If you are

unfamiliar with proper electrical wiring connections obtain the services

of a qualified electrician.

Remove the trim from the box and make sure that no parts are

missing by referencing the PARTS illustrations.

THIS RETROFIT ASSEMBLY IS ACCEPTED AS A COMPONENT

OF A LED LUMINAIRE WHERE THE SUITABILITY OF THE

COMBINATION SHALL BE DETERMINED BY CSA OR CANADIAN

AUTHORITIES HAVING JURISDICTION.

_________________________________________________

WARNING- RISK OF FIRE OR ELECTRIC SHOCK

FOR USE WITH HOUSING MODELS: INCANDESCENT HOUSINGS

– COMMERCIAL ELECTRIC HBR5ICAT, HBR5ICRAT, HBR5,

HBR5R, HALO H5T, H5RT, H5ICT, H5RICAT, C7IC, C7ICR, C7ICA,

C7ICRA, C7, C7R, C7S, HBR5000SIC; HALO H7ICT, H7RICT,

H7ICAT, H7RICAT, H7T, H7RT, H27ICT, H27T, H27RT, H750ICAT,

H750RICAT; CORDELIA X5LICAT, X5LICRAT, HBR7LICAT,

HBR7LICRAT; CAPRI CR1, CRR1; DMF DH6ICATQ, DH6ICRATQ;

ELCO EL5ICA, EL5RICA; LITHONIA L5, L5R, EL7ICA, EL7RICA;

ELITE B5, B5R, B5IC, B5RIC, B6IC, B6RIC; JUNO IC22, IC22R;

LITHONIA L7X, L7XR; NORA NHIC-17QAT, NHRIC-17QAT;

PROGRESS P187-TG, P87-AT, P184-TG, P84-AT; SEA GULL

11018, 11028; THOMAS PS1, PS1-RM. HALO LED HOUSINGS –

H550ICAT, H550RICAT H750ICAT, H750RICAT.

•Do not alter, relocate, or remove wiring, lampholders, power supply,

or any other electrical component. Installation of the retrofit assembly

requires a person familiar with the construction and operation of the

luminaire’s electrical system and the hazard involved. If not qualified,

do not attempt installation. Contact a qualified electrician.

•Do not make or alter any open holes in an enclosure of wiring or

electrical components during kit installation.

•To prevent wiring damage or abrasion, do not expose wiring to edges

of sheet metal or other sharp objects.

____________________________

ASSEMBLY AND INSTALLATION

1. If the installed housing does not have TORSION SPRING SLOTS

or C-CLIPS (FIG. 4) then remove the SCREWS securing the

TORSION SPRINGS to the HEATSINK. Attach the FRICTION

BLADES (included) to the same location using the SCREWS that

were previously removed. (FIG. 1)

2. If using a 5 inch housing, loosen the screws on the TORSION

SPRINGS (or FRICTION BLADES) and slide the brackets inward.

Re-tighten screws to secure TORSION SPRINGS (or FRICTION

BLADES) in place. (FIG. 2)

INCANDESCENT HOUSINGS

1. Unscrew the WING NUT inside the CAN to detach the SOCKET

BRACKET from the CAN. Disengage the SOCKET from the

SOCKET BRACKET. (FIG. 3)

2. Thread the SOCKET ADAPTER into the SOCKET. (FIG. 4)

3. Plug the FEMALE CONNECTOR of the RETROFIT TRIM onto the

MALE CONNECTOR of the SOCKET ADAPTER ASSEMBLY.

(FIG. 5)

4. If using TORSION SPRINGS, squeeze both TORSION SPRING

arms together and insert into the TORSION SPRING SLOTS (or

C-CLIPS) of the CAN. (FIG. 6)

5. Tuck all wires into the CAN and carefully push the RETROFIT

TRIM into CAN. (NOTE: To provide enough room in shallow cans,

carefully position SOCKET ADAPTER and SOCKET adjacent to

the side of the LED DRIVER prior to inserting the RETROFIT

TRIM into the CAN.) (FIG. 4 & 6)

LED HOUSINGS

1. Plug the FEMALE CONNECTOR of the RETROFIT TRIM onto the

MALE CONNECTOR of the HALO HOUSING. (FIG. 5)

2. If using TORSION SPRINGS, squeeze both TORSION SPRING

arms together and insert into the TORSION SPRING SLOTS (or

C-CLIPS) of the CAN. Tuck all wires into the CAN and carefully

push the RETROFIT TRIM into CAN. (FIG. 6)

REV 04-AUG-14

5 in. – 7 in.

5 in. – 6 in.

PARTS

SOCKET ADAPTER

ASSEMBLY

RETROFIT TRIM

COMPATIBLE HOUSING

DIMENSIONS

FIG. 1

FIG. 2

FIG. 3 FIG. 4

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - 1-800-345-0542

WARNING - RISK OF ELECTRIC SHOCK. DISCONNECT MAIN POWER AT FUSE OR CIRCUIT BREAKER BEFORE INSTALLING OR SERVICING THE FIXTURE.LED5” & 6” RETROFIT

Seite 2 - CAUTION:

FIG. 5FIG. 6FIG. 7C D LMODEL: CDLP350R15Class 2 Power SupplyDimmable LED DriverCONFORMS TO UL STD.8750CERTIFIED TO CSA STD C22.2 NO.233MEETS ICES-003C

Seite 3 - MODELO CER6730A

REV 04-AUG-14ADVERTENCIA: RIESGO DE DESCARGA ELÉCTRICA. DESCONECTE EL SUMINISTRO ELÉCTRICO DE LA CAJA DE FUSIBLES O LOS INTERRUPTORES DE CIRCUITO ANTE

Seite 4 - ADVERTENCIA:

Seite 5 - REV 04-AUG-14

REV 04-AUG-14AVERTISSEMENT – RISQUE DE DÉCHARGE ÉLECTRIQUE. COUPEZ LE COURANT AU NIVEAU DU DISJONCTEUR OU DE LA BOÎTE DE FUSIBLES AVANT D’INSTALLER O

Seite 6