Commercial Electric CER3G10R343WHP Bedienerhandbuch PDF herunterladen (Seite 3)

1. Insert the light bulb into the socket and twist clockwise to lock it in place.

2. Secure the bulb to the trim assembly by angling it into its mounting clip.

3. Slide the trim assembly into the housing until it snaps into the place.

4. Installation is complete. Restore electrical power.

LIGHT BULB AND TRIM INSTALLATION (Fig. 15 & 16)

Fig. 15

Fig. 16

TROUBLESHOOTING

Wall sw itch or circuit breaker is

off.

Turn on sw itch or circuit breaker.

Incorrect or loose w ire

connections

Check wire connections

Light bulb may be dead. Test light

bulb in a know n w orking light

fixture.

Replace light bulb.

Light bulb is loose. Tighten light bulb in socket.

The light is turning off

after being on for

some time. Soon after,

it turns back on. The

light continues this

cycle indefinitely.

The thermal sensor turning off

due to excessive heat.

Space aw ay any insulation at

least 3" (7,6 cm) from the

housing, as show n in Fig. 1.

The light does not turn

on.

SYMPTOM POSSIBLE CAUSE SOLUTION

Cable

Junction

box

door

Wire

nut

Housing

Metal tab

BX Cable

connector

Fig. 13

Fig. 14

Knockout

Housing

NOTE: In additional to the main supply cable entering the junction box, one

more cable may be fed into the junction box to provide electrical power to

another light fixture intended to be on the same circuit. No more than two

cables can be fed into the junction box. It is very important that the knockout

used for the second cable be adjacent to the knockout used for the first

cable. Avoid using a knockout that is on the opposite side of the first

knockout. Using an opposite knockout may make insertion through the

ceiling hole more difficult.

1. Open the junction box’s door by pulling on its metal tab.

2. Break off one of the round knockouts from the junction box using a

screwdriver. Secure an appropriately sized BX or NM (Romex) cable

connector to the knockout opening. Feed the BX or NM (Romex) cable

through the connector, providing 3” (7,6 cm) of slack inside the junction

box. Tighten the connector to secure the cable in place.

3. Remove at least 3” (7,6 cm) of the cable’s outer sheath and remove the

plastic or paper over-wrap. Strip approximately 3/8” (1,0 cm) of insulation

from the ends of all supply wires. Using wire nuts, make the following wire

connections:

WHITE SUPPLY WIRE (NEUTRAL) TO WHITE FIXTURE WIRE

BLACK SUPPLY WIRE (HOT) TO BLACK FIXTURE WIRE

GREEN/BARE SUPPLY WIRE (GRND) TO GREEN FIXTURE WIRE

ELECTRICAL CONNECTIONS (Fig. 13 & 14)

Be sure that there are no loose strands or loose wires.

4. Wrap all wire connections with electrical tape for a more secure

connection. NOTE: If you have electrical questions, consult your

local electrical code for approved grounding methods.

5. Carefully stuff all wires and wire connections into the junction box. Close

the junction box’s door.

DROP CEILING INSTALLATION

1. Install a ceiling tile onto the T-bar grid at the installation location. Using the

provided template and a keyhole saw make a hole at the desired location in

the ceiling tile.

2. Place the plaster frame/hanger bar assembly onto the ceiling tile into the

newly created hole, making sure the bottom of the plaster frame feeds

through the hole. Adjust the width of both hanger bars to the distance

between the two T-bars, aligning each mounting clip with the top of its

corresponding T-bar. Press down on all mounting clips until they snap onto

the T-bar. NOTE: Holes are provided on the mounting clips that can be

used to secure the hanger bars to the T-bar. Parts (I.e. screws, hex nuts)

can be purchased separately for this purpose.

NOTE: Drop ceiling installations are similar to new construction

installations, except the hanger bars are attached to the T-bars of a drop

ceiling grid, instead of ceiling joists, as described below.

T-BAR INSTALLATION (Fig. 12)

T-bar

Ceiling

tile

Hole

Plaster

frame

Hanger

bar

Mounting

clip

Fig. 12

3. Proceed to Step 3 of the “CEILING JOIST INSTALLATION” section.

Light

bulb

Trim

Socket

Housing

1 2 3 4 5 6 7 8 9

Kommentare zu diesen Handbüchern

Keine Kommentare

Commercial Electric CER3G10R343WHP Bedienerhandbuch Seite 3

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein Commercial Electric CER3G10R343WHP